Aramco Approved Manufacturer
image
image

Elastomeric Fire Caulk – INSS1186

KEY TECHNICAL DATA

Industry leading Firestop Technology, INSS1186 Elastomeric FireCaulk is a water based acrylic elastomeric resin material that offers excellent flexibility even after full curing. lNSS1186 is tested in accordance with UL 2079 and ULC S-115 for use on dynamic construction joints system, such as Head of Wall, Wall to Wall, Floor to Wall and Floor to Floor joints. INSS1186 can be applied by brush, bulk caulking gun, trowel or airless sprayer. It is compatible with and adheres to common construction materials and it withstands compression and extension in dynamic joints, without losing its adhesion.

INSS1186 Elastomeric FireCaulk is a water based, low VOC, halogen, asbestos and organic solvent free product. Meets the intent of LEED® VOC environmental air quality requirements

INSTALLATION GUIDE
  1. Refer to applicable certification directory or www.painttoprotect.com for listed assemblies.
  2. Remove surface contaminants such as dirt, oil, rust or other previous adhesive, to ensure a clean surface for excellent adhesion.
  3. Mineral wool batt may be required in joint systems. Install min 64 kg/m3 (4 pcf) mineral wool batt insulation in joint opening as a permanent form. Install edge-first into joint opening, parallel with joint direction, such that batt sections are compressed min 60 percent in thickness and flush with bottom surfaces of the floor.
  4. Using airless sprayer or brush, apply required wet thickness of INSSS1186 to completely cover top surface of mineral wool and lap additional 2 mm (5/64 in.) thick by min 25 mm (1 in.) onto each edge of substrate. Product can be applied to vertical or horizontal surfaces. To avoid sag when applied to vertical surfaces, install 2-3 thinner applications until required depth is achieved, allowing it to cure slightly between coats.
  5. Trowel by using a mason’s trowel or putty knife as needed.
  6. Can be applied to vertical or horizontal surface – to avoid sag when applied to vertical surfaces install 2-3 thinner applications until required depth is achieved, allow to cure slightly between coats.
  7. Full curing may take 3-7 days, depending on the applied thickness and ambient condition. Avoid contact with moisture prior to fully curing.
image
FEATURES

Density: 1.5±0.1 g/cm3
Solid Content (by weight): 75%
pH value: 3-7
VOC: 4 g/L
Dry to Touch: 30 minutes
Curing Time: 3-7 DAYS
Application Temp: 40° F – 104° F (5° C – 40° C)
In-Service Temp: -13° F – 176° F (-25° C – 80° C) Shelf life:
24 months
Maximum cyclic displacement: ±12.5%
Storage Temperature: 50°F – 95° F (10° C – 35° C)
Packaging: 600 ml/Sausage, 20/ctn; 1 G/Pail, 5G/Pail
Performance: 50+ years HOAC tested

APPLICATIONS
image

Elastomeric Fire Caulk – INSS1186

Aramco Approved Manufacturer
image
image
image
KEY TECHNICAL DATA

Industry leading Firestop Technology, INSS1186 Elastomeric FireCaulk is a water based acrylic elastomeric resin material that offers excellent flexibility even after full curing. lNSS1186 is tested in accordance with UL 2079 and ULC S-115 for use on dynamic construction joints system, such as Head of Wall, Wall to Wall, Floor to Wall and Floor to Floor joints. INSS1186 can be applied by brush, bulk caulking gun, trowel or airless sprayer. It is compatible with and adheres to common construction materials and it withstands compression and extension in dynamic joints, without losing its adhesion.

INSS1186 Elastomeric FireCaulk is a water based, low VOC, halogen, asbestos and organic solvent free product. Meets the intent of LEED® VOC environmental air quality requirements

INSTALLATION GUIDE
  1. Refer to applicable certification directory or www.painttoprotect.com for listed assemblies.
  2. Remove surface contaminants such as dirt, oil, rust or other previous adhesive, to ensure a clean surface for excellent adhesion.
  3. Mineral wool batt may be required in joint systems. Install min 64 kg/m3 (4 pcf) mineral wool batt insulation in joint opening as a permanent form. Install edge-first into joint opening, parallel with joint direction, such that batt sections are compressed min 60 percent in thickness and flush with bottom surfaces of the floor.
  4. Using airless sprayer or brush, apply required wet thickness of INSSS1186 to completely cover top surface of mineral wool and lap additional 2 mm (5/64 in.) thick by min 25 mm (1 in.) onto each edge of substrate. Product can be applied to vertical or horizontal surfaces. To avoid sag when applied to vertical surfaces, install 2-3 thinner applications until required depth is achieved, allowing it to cure slightly between coats.
  5. Trowel by using a mason’s trowel or putty knife as needed.
  6. Can be applied to vertical or horizontal surface – to avoid sag when applied to vertical surfaces install 2-3 thinner applications until required depth is achieved, allow to cure slightly between coats.
  7. Full curing may take 3-7 days, depending on the applied thickness and ambient condition. Avoid contact with moisture prior to fully curing.
FEATURES

Density: 1.5±0.1 g/cm3
Solid Content (by weight): 75%
pH value: 3-7
VOC: 4 g/L
Dry to Touch: 30 minutes
Curing Time: 3-7 DAYS
Application Temp: 40° F – 104° F (5° C – 40° C)
In-Service Temp: -13° F – 176° F (-25° C – 80° C) Shelf life:
24 months
Maximum cyclic displacement: ±12.5%
Storage Temperature: 50°F – 95° F (10° C – 35° C)
Packaging: 600 ml/Sausage, 20/ctn; 1 G/Pail, 5G/Pail
Performance: 50+ years HOAC tested

APPLICATIONS
image