Approved Manufacturer
image
image

Cable Coating – DC6150

KEY TECHNICAL DATA

DC6150 Cable Coating is a non-halogenated, asbestos-free, non-toxic, flexible, ablative fire retardant cable coating designed to prevent the propa- gation of fire along plastic jacketed electrical cables. DC 6150 Cable Coating is FM Approved and tested to ensure it can withstand extreme conditions such as freeze/thaw cycles and salt water immersion. This testing also ensures that the protective coating does not de-rate the cables current car- rying capacity. DC 6150 Cable Coating is a water based latex and is suitable for both interior and exterior use.

INSTALLATION GUIDE
  1. Surfaces to be coated must be clean and dry. Use a dry rag to remove any oil, grease and dirt prior to coating application.
  2. Mix DC6150 cable coating throughly by a power agitator before application. Thinner is normally not required. If Nacessary, use potable water (3% max.) to adjust viscosity. Water is also used for tools and spray machine cleaning.
  3. Coating can be applied by means of airless spray equipment in a single pass, not more than 1mm-1.2mm (wet coating thickness) to prevent slumping. Surface shall be measured using a wet film thickness gauge. If applying coating by brush or roller, it may be required to apply thinner coat to prevent slumping. The coating should be applied when site temperature is between 4°C (40°F) and 40°C (104°F). Temperature must be maintained until coating has fully dried.
  4. Recommended coating thickness on cables: 2.5mm WFT results in 1.6mm dry. Verify the DFT by using calipers to measure the cable before coating and once coating has fully dried.
  5. Do not allow the coating material to remain in hoses, gun or spray equipment. Clean all the equipment with water immediately after use.
  6. All unused coating should be stored in tightly closed container. Surface skinning may show in a partially filled container
image
FEATURES

Color: White
Odor: Mild Lated
Gloss Level: Matt
Specific Gravity: 1.55 ± 0.1
Solids by Weight: 70~76%
pH Value: 6 ~ 8
V.O.C.: 28 g/L
Dry to Touch: 2 ~ 4 hours
Dry Through: 2 ~ 4 days (Depending on ambient conditions)
Application: Airless spray, brush or roller
In-Service Temp: -13° F – 176° F (-25° C – 80° C)
Typical Thickness: 1000 microns WFT (39.5 mils) equivalent to 640 microns DFT (25 mils)
Packaging: 25Kg/pail
Shelf Life: 12 months

APPLICATIONS
image

Cable Coating – DC6150

Approved Manufacturer
image
image
image
KEY TECHNICAL DATA

DC6150 Cable Coating is a non-halogenated, asbestos-free, non-toxic, flexible, ablative fire retardant cable coating designed to prevent the propa- gation of fire along plastic jacketed electrical cables. DC 6150 Cable Coating is FM Approved and tested to ensure it can withstand extreme conditions such as freeze/thaw cycles and salt water immersion. This testing also ensures that the protective coating does not de-rate the cables current car- rying capacity. DC 6150 Cable Coating is a water based latex and is suitable for both interior and exterior use.

INSTALLATION GUIDE
  1. Surfaces to be coated must be clean and dry. Use a dry rag to remove any oil, grease and dirt prior to coating application.
  2. Mix DC6150 cable coating throughly by a power agitator before application. Thinner is normally not required. If Nacessary, use potable water (3% max.) to adjust viscosity. Water is also used for tools and spray machine cleaning.
  3. Coating can be applied by means of airless spray equipment in a single pass, not more than 1mm-1.2mm (wet coating thickness) to prevent slumping. Surface shall be measured using a wet film thickness gauge. If applying coating by brush or roller, it may be required to apply thinner coat to prevent slumping. The coating should be applied when site temperature is between 4°C (40°F) and 40°C (104°F). Temperature must be maintained until coating has fully dried.
  4. Recommended coating thickness on cables: 2.5mm WFT results in 1.6mm dry. Verify the DFT by using calipers to measure the cable before coating and once coating has fully dried.
  5. Do not allow the coating material to remain in hoses, gun or spray equipment. Clean all the equipment with water immediately after use.
  6. All unused coating should be stored in tightly closed container. Surface skinning may show in a partially filled container
FEATURES

Color: White
Odor: Mild Lated
Gloss Level: Matt
Specific Gravity: 1.55 ± 0.1
Solids by Weight: 70~76%
pH Value: 6 ~ 8
V.O.C.: 28 g/L
Dry to Touch: 2 ~ 4 hours
Dry Through: 2 ~ 4 days (Depending on ambient conditions)
Application: Airless spray, brush or roller
In-Service Temp: -13° F – 176° F (-25° C – 80° C)
Typical Thickness: 1000 microns WFT (39.5 mils) equivalent to 640 microns DFT (25 mils)
Packaging: 25Kg/pail
Shelf Life: 12 months

APPLICATIONS
image