image

Fireproof Cable Coating – DC310

KEY TECHNICAL DATA

DC310 Fireproof Cable Coating for wires and cable is developed using innovative intumescent technology. It is a heavy duty intumescent coating for interior applications used to effectively prevent flame spread. When fire occurs, the coating will rapidly intumesce to form a foam char layer that prevents fire propagation. DC310 fireproof cable coating is water based, asbestos-free, non-halogenated and environmentally–friendly. DC310 is able to protect cables for up to 90 minutes depending on application thick- ness and cable type

INSTALLATION GUIDE
  1. Surfaces to be coated must be clean and dry. Use a dry rag to remove any oil, grease and dirt prior to coating application.
  2. Mix DC310 cable coating throughly by a power agitator before application. Thinner is normally not required. If Nacessary, use potable water (3% max.) to adjust viscosity. Water is also used for tools and spray machine cleaning.
  3. Coating can be applied by means of airless spray equipment in a single pass, not more than 1mm-1.2mm (wet coating thickness) to prevent slumping. Surface shall be measured using a wet film thickness gauge. If applying coating by brush or roller, it may be required to apply thinner coat to prevent slumping. The coating should be applied when site temperature is between 4°C (40°F) and 40°C (104°F). Temperature must be maintained until coating has fully dried.
  4. Verify the DFT by using calipers to measure the cable before coating and once coating has fully dried.
  5. Do not allow the coating material to remain in hoses, gun or spray equipment. Clean all the equipment with water immediately after use.
  6. All unused coating should be stored in tightly closed container. Surface skinning may show in a partially filled container. Filter the material prior use.
image
FEATURES

Color: White
Finish: Flat
Density: 1.3±0.1 kg/L
Viscosity: 10000-25000cps(25°C);
Adjustable PH: 7.5±0.5 VOC: 56 g/L
Typical thickness: 1mm WFT equivalent to 0.6mm DFT
Solid content: ³60% Volume
Storage temp: 40° F – 104° F (5° C – 40° C)
Drying time (25° C): 3-4 hours touch dry, 24 hours dried through
Application Temp: 40° F – 104° F (5° C – 40° C)
In-Service Temp: -13° F – 176° F (-25° C – 80° C)
Packaging: 25 kg/pail
Shelf life: 12 months

APPLICATIONS
image

Fireproof Cable Coating – DC310

image
image
KEY TECHNICAL DATA

DC310 Fireproof Cable Coating for wires and cable is developed using innovative intumescent technology. It is a heavy duty intumescent coating for interior applications used to effectively prevent flame spread. When fire occurs, the coating will rapidly intumesce to form a foam char layer that prevents fire propagation. DC310 fireproof cable coating is water based, asbestos-free, non-halogenated and environmentally–friendly. DC310 is able to protect cables for up to 90 minutes depending on application thick- ness and cable type

INSTALLATION GUIDE
  1. Surfaces to be coated must be clean and dry. Use a dry rag to remove any oil, grease and dirt prior to coating application.
  2. Mix DC310 cable coating throughly by a power agitator before application. Thinner is normally not required. If Nacessary, use potable water (3% max.) to adjust viscosity. Water is also used for tools and spray machine cleaning.
  3. Coating can be applied by means of airless spray equipment in a single pass, not more than 1mm-1.2mm (wet coating thickness) to prevent slumping. Surface shall be measured using a wet film thickness gauge. If applying coating by brush or roller, it may be required to apply thinner coat to prevent slumping. The coating should be applied when site temperature is between 4°C (40°F) and 40°C (104°F). Temperature must be maintained until coating has fully dried.
  4. Verify the DFT by using calipers to measure the cable before coating and once coating has fully dried.
  5. Do not allow the coating material to remain in hoses, gun or spray equipment. Clean all the equipment with water immediately after use.
  6. All unused coating should be stored in tightly closed container. Surface skinning may show in a partially filled container. Filter the material prior use.
FEATURES

Color: White
Finish: Flat
Density: 1.3±0.1 kg/L
Viscosity: 10000-25000cps(25°C);
Adjustable PH: 7.5±0.5 VOC: 56 g/L
Typical thickness: 1mm WFT equivalent to 0.6mm DFT
Solid content: ³60% Volume
Storage temp: 40° F – 104° F (5° C – 40° C)
Drying time (25° C): 3-4 hours touch dry, 24 hours dried through
Application Temp: 40° F – 104° F (5° C – 40° C)
In-Service Temp: -13° F – 176° F (-25° C – 80° C)
Packaging: 25 kg/pail
Shelf life: 12 months

APPLICATIONS
image